Radio waves around us: WiFi, Bluetooth, mobile networks and satellite straight to the phone
Contents 12
- In short
- What a radio wave is
- How a wave gets to us
- Walls and materials
- Neighbours' WiFi and other interference
- Mobile signal when coverage is poor
- A satellite straight to your phone: Starlink Direct to Cell
- Radio waves and health
- Decibels without fear
- Will a booster help
- What to do when the signal is poor
- Sources
The radio waves around us every day: WiFi, Bluetooth, mobile networks, GPS, key fobs and the microwave oven. In this article:
- what frequency and wavelength are, and which frequencies everyday devices use;
- how a radio wave covers distance and gets past obstacles, and why lower frequencies reach further;
- which walls and materials block the signal the most;
- your neighbours' WiFi: channels, channel width, why 5 GHz works better in a block of flats, and what else is noisy at 2.4 GHz;
- poor mobile signal: where to look for coverage, how to find the mast, what RSRP, RSRQ and SINR mean;
- Starlink Direct to Cell and Kyivstar: how a satellite talks to an ordinary phone, and why it does not replace the ground network;
- health: what is known for certain and what is not;
- decibels in plain words;
- whether a booster helps, and what to do when the signal is poor.
There are no measurements of our own in this article: the figures come from reference books, standards and operator announcements (sources at the end). Ranges, losses and "good / poor" thresholds are rough guides: they depend heavily on the building, the device and the terrain.
In short
| Question | Answer |
|---|---|
| Why is WiFi worse in the far room | every wall takes some of the signal; concrete and reinforced concrete take the most |
| 2.4 GHz or 5 GHz | 2.4 GHz reaches further and through walls; 5 GHz is faster with fewer neighbours, but shorter range |
| Poor mobile signal indoors | get to a window facing the mast, go higher up; use WiFi calling (VoWiFi) |
| Will Starlink Direct to Cell replace the network | no: it is a fallback outdoors where there is no ground network — texts and "light data" |
| Are radio waves harmful | the only proven effect is heating, and the limits have a wide margin; mild caution does no harm |
| Will a booster help | for WiFi, a second access point or mesh; for mobile, only one approved by your operator |
What a radio wave is
A radio wave is an electromagnetic wave, the same in nature as light, only at a much lower frequency. It travels at the speed of light, about 300,000 km per second.
Frequency is how many times the wave oscillates per second. It is measured in hertz: 1 MHz is a million oscillations per second, 1 GHz a billion. Wavelength is the distance the wave travels during one oscillation. The two are linked by a simple rule: wavelength = speed of light ÷ frequency. That gives a handy shortcut: wavelength in metres ≈ 300 ÷ frequency in megahertz.
Wavelength matters in practice. It sets the size of the antenna (the simplest antenna is a quarter or half a wavelength long), and it shapes how the wave behaves around obstacles: objects much smaller than the wavelength barely affect it, while larger ones reflect it or cast a radio shadow.
Frequencies around us
| What | Frequency | Wavelength (calc.) |
|---|---|---|
| FM radio | 87.5–108 MHz | about 3 m |
| car key fobs, sensors, weather stations | 433 MHz, 868 MHz | 69 cm / 35 cm |
| mobile networks, low bands | 700, 800, 900 MHz | 43–33 cm |
| GPS (main L1 signal) | 1575.42 MHz | 19 cm |
| mobile networks, mid bands | 1800, 2100, 2600 MHz | 17–12 cm |
| DECT cordless home phones (Europe) | 1880–1900 MHz | 16 cm |
| Bluetooth, 2.4 GHz WiFi | 2400–2483.5 MHz | 12.5 cm |
| microwave oven | 2450 MHz | 12 cm |
| 5G (one of its most widely used bands) | around 3.5 GHz | 8.6 cm |
| 5 GHz WiFi | 5150–5725 MHz (in Europe, in sections) | about 6 cm |
| 6 GHz WiFi (WiFi 6E and WiFi 7) | 5945–6425 MHz (in Europe) | about 5 cm |
Mobile networks do not use a single frequency but several bands: 2G, 3G, 4G and 5G can each sit in different ones, and the mix depends on the country and the operator. In Ukraine, 4G mostly runs on 900, 1800, 2100 and 2600 MHz (as far as we know; the list changes).
Key fobs and sensors on 433 and 868 MHz are a topic of their own: we looked at whether a lost car key can be found with a 433 MHz receiver and how to build your own beacon tag. The same 433 MHz band is used by tyre pressure sensors, which you can pick up with a cheap RTL-SDR receiver.
How a wave gets to us
Between transmitter and receiver, a wave can travel along several paths at once:
| Effect | What happens | Where you notice it |
|---|---|---|
| line of sight | the wave goes in a straight line with nothing in the way | GPS satellites, a mast across an open field |
| reflection | the wave bounces off metal, concrete, water, the ground | in a city the signal arrives "round the corner" off buildings |
| diffraction | the wave bends round the edge of an obstacle: a roof, a hill, a building corner | behind a hill the signal is weaker but does not vanish |
| absorption | the material turns part of the wave's energy into heat | walls, trees in leaf, water, people |
Indoors, WiFi almost never arrives along a single straight path: the phone receives copies of the signal reflected off walls and furniture. That is why moving the phone a few centimetres can sometimes change the signal noticeably.
The main rule behind most everyday situations:
Lower frequency: further and better through walls. Higher frequency: faster, but shorter range.
Why: at higher frequencies most materials absorb more energy, and waves bend round obstacles less. At the same time, it is easier to find wide channels at higher frequencies, and a wider channel means more speed. So operators keep 800–900 MHz for covering large areas and reaching inside buildings, and use 1800–2600 MHz and 3.5 GHz for speed where there are lots of people.
⚠ There is another reason lower frequencies "reach further": the antenna. A phone antenna of the same size collects more energy from the air at a lower frequency. In empty space, the wave itself weakens with distance in the same way at any frequency.
The Fresnel zone
Line of sight is not a thin line between two antennas but a "cigar" around that line, called the first Fresnel zone. If something pokes into that cigar — a roof, treetops, a hill — the signal weakens, even when you can see the other antenna with your own eyes.
Halfway along the path, the radius of this zone is roughly 8.7 × √(distance in km ÷ frequency in GHz) metres. For a 1 km link at 2.4 GHz that is about 5.6 m. The usual rule of thumb is to keep at least 60% of that radius clear, here about 3.4 m. That is why antennas for links between buildings go above roofs and trees, not just high enough to "see" each other.
Typical ranges
| What | Rough range | Depends on |
|---|---|---|
| Bluetooth: earbuds, a watch | up to 10 m in a room | device class, a person's body in between |
| Bluetooth Low Energy outdoors | tens of metres | power, antenna, Bluetooth version |
| WiFi in a flat | one access point covers 1–3 rooms through walls | wall material, 2.4 / 5 GHz band |
| WiFi outdoors (phone to router) | tens of metres, up to about a hundred with line of sight | antennas, obstacles, power |
| mobile mast in a city | hundreds of metres to a few kilometres | buildings, number of users, frequency |
| mobile mast in open country | a few to tens of kilometres | mast height, terrain, frequency |
Often, WiFi range is limited by the phone rather than the router: the router transmits more power and has better antennas, so the phone may see the network while its reply no longer reaches the router.
Walls and materials
Every obstacle takes away some of the signal. How much depends on thickness, moisture, the amount of rebar, and frequency. The figures below are rough ranges for 2.4 GHz from reference measurements; at 5 GHz losses are usually higher.
| Material | Loss | Roughly, 2.4 GHz | Note |
|---|---|---|---|
| plasterboard partition | low | 2–4 dB | a bit more on a metal stud frame |
| timber wall, door | low | 3–6 dB | damp wood blocks more than dry |
| ordinary glass | low | 1–3 dB | |
| brick | noticeable | 6–12 dB | depends on thickness and whether the bricks are hollow |
| concrete | high | 10–20 dB or more | a load-bearing wall in a panel block is the classic "no WiFi" wall |
| reinforced concrete | high | 15–30 dB or more | the rebar mesh acts like a screen |
| low-emissivity (metal-coated) glass | high | 20–40 dB | a thin metal layer on the glass; mobile signal by the window drops |
| mirror | high | varies | the metal backing reflects |
| water: aquarium, hot water tank, people | noticeable | a person: a few dB | water absorbs radio waves well, more so at higher frequencies; a full aquarium is a big obstacle |
| metal: lift, fridge, steel door | very high | almost total | the signal can only go round |
What 10 dB of loss means is explained in the section on decibels: in short, a tenth of the power. Two concrete walls between router and phone can cost as much as moving tens of times further away from the router in free space.
⚠ Energy-saving windows are a common reason why mobile signal is worse in a new building than in an old one, even with the same mast. Outside the glass there is signal; in the room, barely any. An open window, a balcony with ordinary glass, or WiFi calling helps.
Neighbours' WiFi and other interference
WiFi is shared radio. When several networks use the same channel they do not "merge"; they take turns, with each router waiting until the air is free. The more neighbours on your channel, the less airtime you get, and speed drops even with a strong signal.
2.4 GHz channels
The 2.4 GHz band is narrow: in Europe it has 13 channels spaced 5 MHz apart, while one WiFi channel is 20 MHz wide. So neighbouring channels overlap. Only three fit without overlapping: 1, 6 and 11.
| What to do | Why |
|---|---|
| pick 1, 6 or 11 | a network on the same channel takes turns with you in an orderly way; one on an adjacent channel just adds noise |
| avoid 3, 4, 8, 9 | such a channel straddles two clean ones, so it interferes with both and picks up interference from both |
| use 20 MHz channel width | 40 MHz at 2.4 GHz takes up almost half the band, which makes things worse in a block of flats |
| see what is on the air | a WiFi analyser app on a phone or laptop shows your neighbours' networks and their channels |
| automatic channel selection is fine | modern routers choose reasonably well; if not, set the least busy of 1, 6, 11 |
Why 5 GHz works better in a block of flats
There are far more channels at 5 GHz, and you share them with neighbours less often. The fact that 5 GHz gets through walls worse becomes an advantage here: neighbours' networks behind a concrete wall are barely audible, so the air in your flat is quieter. The downside is range: 5 GHz may not reach the far room, and then a second access point helps (see the section on boosters).
Channel width at 5 GHz is usually set to 80 MHz, a good compromise between speed and the number of free channels. 160 MHz only makes sense if it really is quiet around you.
The 6 GHz band (WiFi 6E and WiFi 7) is even emptier, but gets through walls even worse and needs support from both router and phone. Whether the band is open to WiFi in your country is up to the regulator, so it is worth checking.
What else is noisy at 2.4 GHz
The 2.4 GHz band needs no licence, so lots of different devices use it.
| Source | Does it interfere with WiFi |
|---|---|
| microwave oven | yes, while running: it heats at 2.45 GHz and its shielding is not perfect; channels near 2.45 GHz, in the middle and upper part of the band, suffer most |
| analogue wireless cameras, video baby monitors | yes, if they use 2.4 GHz and transmit continuously; they can occupy part of the band all the time |
| Bluetooth | hardly: it hops between frequencies and avoids busy ones |
| DECT cordless home phones | no: in Europe DECT uses 1880–1900 MHz; the troublemakers were older cordless phones that ran at 2.4 GHz |
| USB 3.0: cables, hubs, flash drives | yes, close by: USB 3.0 noise reaches 2.4 GHz; a wireless mouse receiver next to a USB 3.0 port lags |
| cheap power supplies, LED drivers | sometimes: poorly filtered switching circuits emit broadband noise |
Checking for interference is easy: switch off the suspect device and see whether the speed changes. For a mouse or headset receiver next to a USB 3.0 port, a short USB extension cable that moves the receiver away from the port helps.
⚠ Standards for microwave ovens allow a small amount of leakage; noticeable WiFi interference does not by itself mean the oven is faulty. But if the door is damaged or does not close tightly, the oven should be repaired or replaced.
Mobile signal when coverage is poor
The signal reaches your phone from a mast, and along the way it is weakened by distance, terrain, buildings and walls. So finding a better spot means finding the path to the mast with the fewest obstacles:
- closer to a window, ideally on the side facing the mast: a wall between phone and mast takes more than glass does (unless it is metal-coated);
- higher up: on upper floors and on hills there are fewer buildings in the way; basements and ground floors are worse;
- in the open: in a field or on a hill you may get signal where there is none in the valley;
- out of the car if you can: a metal body and tinted windows weaken the signal too.
Where is the mast
Mast locations are shown on maps built by users themselves: an app on the phone records which signal it sees and from which mast, and thousands of such records make up a map. The best known is CellMapper; there are others. These maps are not precise: a mast on them is an estimate from measurements, not an address from official records. But they usually point you in the right direction.
The simpler way is to look around: masts often stand on the roofs of tall buildings, on standalone masts by roads, or on water towers.
RSRP, RSRQ, SINR
The signal bars on a phone screen are a rough summary, and every manufacturer draws them differently. The more precise 4G numbers are shown in the phone's engineering menu or in network analysis apps. On Android, some of them are in the settings ("About phone" → "Status" → "SIM status"; menu names vary by manufacturer).
Why are these numbers tucked away? Probably because they mean nothing to most people without an explanation, whereas bars are "obvious to everyone".
| Metric | What it means | Good | Fair | Poor |
|---|---|---|---|---|
| RSRP | signal power from the mast (dBm) | above −90 dBm | −90…−105 dBm | below −105 dBm |
| RSRQ | quality: how well the useful signal stands out from everything else on the air (dB) | above −10 dB | −10…−15 dB | below −15 dB |
| SINR | signal-to-interference-plus-noise ratio (dB) | above 13 dB | 0…13 dB | below 0 dB |
The thresholds are rough: different sources place them a few decibels apart. At around −120 dBm RSRP the connection is usually about to drop.
How to read them together: strong RSRP with poor SINR means the signal is there but other masts or interference are drowning it out. Moving a few metres helps less than it would with a weak signal. Weak RSRP with decent SINR means the signal simply is not getting through: move closer to a window or higher up.
What else helps
- Don't hold the phone over its antenna. Antennas usually sit at the top and bottom of the case; a hand wrapped tightly round the phone weakens the signal. The same goes for a phone in your back pocket: the body absorbs the signal (see the section on the body).
- Lock the network mode. When 4G is barely there, the phone keeps switching between 4G and 3G/2G, and the connection keeps dropping. In the settings you can choose "3G only" or "4G only" and see which is more stable. For calls, 2G/3G is sometimes more reliable; for data, 4G even with a weak signal. ⚠ Only choose "4G only" if your phone and plan support calls over 4G (VoLTE); otherwise calls will not work at all. Bear in mind that operators are gradually switching off older networks, so one of them may already be gone in your area.
- WiFi calling (VoWiFi). If you have internet at home, the phone can make calls over WiFi just as it does through the mast, with the same number and without extra apps. In Ukraine the major operators support it, but not on every phone model: look for the switch in the call or SIM settings, and check with your operator whether your phone is supported.
- Messaging apps over WiFi do the same for the people you talk to on Viber, WhatsApp, Signal or Telegram.
A satellite straight to your phone: Starlink Direct to Cell
How it works
Ordinary Starlink means a dish on the roof. Direct to Cell is different: the satellites carry a 4G base station, effectively a mobile mast lifted into low orbit. It runs on ordinary 4G frequencies provided by the partner operator. To the phone, the satellite looks like just another mast on its network, so no new phone or extra antenna is needed.
What follows from that:
- you need open sky: the satellite is far away and the signal is weak; indoors, in a forest in full leaf, or between tall buildings there may be no connection;
- the satellite moves: it crosses the visible part of the sky in a few minutes, and the phone hands over from one satellite to the next; the connection sometimes drops;
- texts first, then "light data": speeds are low, so the service started with messages and later added selected apps.
Kyivstar
| Date | What happened |
|---|---|
| 24 November 2025 | Starlink Direct to Cell launched, the first in Europe; texts only at first, on 4G-capable Android smartphones, free within the customer's plan |
| 15 January 2026 | more than 3 million customers had registered on the satellite network, sending more than 1.2 million texts; iPhone testing began |
| 16 June 2026 | "light data" in test mode: Viber, WhatsApp, Google Maps — text, photos, voice and video messages, navigation; Android with 4G, with the "There's a Connection" option on the plan; this is not full internet access |
| 16 June 2026 | by then, reportedly more than 6 million customers had connected to the satellite network |
The phone connects to the satellite by itself when there is no ground network. This matters most where masts have been destroyed or have lost power.
Why it does not replace the ordinary network
People sometimes ask: if you can get a connection even from a satellite, why bother with masts? The reasons are simple:
| Limitation | Explanation |
|---|---|
| capacity shared over a huge area | one satellite beam covers an area that may hold thousands of people; a mast serves a much smaller patch |
| speeds of a few Mbit/s | a few Mbit/s, shared by everyone in the satellite beam; an ordinary 4G mast delivers tens of times more |
| latency | higher than on the ground network: the signal goes up to the satellite and back; it does not matter for messages, but it shows in video calls and games |
| outdoors with a view of the sky only | in a flat with poor signal, the satellite will not help |
| only where there is no mast | the phone switches to the satellite by itself when there is no ground network; you cannot choose "satellite only" |
| depends on operator and country | the service works only through a partner operator and on frequencies licensed in that country |
So Direct to Cell is an add-on: coverage in fields, mountains, on the road, and where the network has been destroyed. It is not a way to improve signal in your flat, and it does not replace the ordinary network.
Other operators
SpaceX's Direct to Cell partners include T-Mobile in the US (the T-Satellite service: public beta from February 2025, full launch in July 2025), One NZ in New Zealand, Optus and Telstra in Australia, Rogers in Canada, Entel in Chile and Peru, KDDI in Japan, and Salt in Switzerland. Each has its own services and timelines.
Radio waves and health
Radio waves are non-ionising radiation. A single "packet" (photon) of radio energy carries hundreds of thousands to millions of times less energy than it takes to break a chemical bond in a molecule. That is the fundamental difference from X-rays, which damage DNA in exactly that way.
At communication frequencies, the only proven effect of radio waves on the body is heating. That is how a microwave oven works: about a kilowatt is concentrated inside a closed cavity. A phone transmits hundreds to thousands of times less (from a fraction of a watt up to about two watts at peak on older networks), and a WiFi router a few tenths of a watt.
Limits are set by bodies such as the International Commission on Non-Ionizing Radiation Protection (ICNIRP). They are derived from the level at which tissue heating becomes noticeable, with a wide margin — tens of times for the general public. For phones, the measure is SAR: how much energy a kilogram of tissue absorbs. In Europe the limit for the head and trunk is 2 W/kg (averaged over 10 g of tissue); every phone model is tested against it, and its SAR value is listed in the documentation.
In 2011 the International Agency for Research on Cancer (IARC) classified radiofrequency fields as Group 2B, "possibly carcinogenic to humans". This means the evidence is limited and can neither confirm nor rule out a link. The same group includes, for example, aloe vera whole-leaf extract and traditional Asian pickled vegetables. Group 2B means the question is open, not that harm has been shown.
Since then there has been far more research. In 2024 a systematic review commissioned by the WHO was published (Karipidis et al., Environment International): it found no link between mobile phone use and brain cancer, including among people who have used phones heavily for a long time.
What is worth knowing so that caution stays sensible:
- a phone at your head gives far more exposure than a mast on the roof: the mast is far away, and field strength drops quickly with distance;
- with poor signal the phone transmits harder: it raises its power so that a distant mast can hear it; with good signal it turns the power down;
- so for long calls, especially with a weak signal, a headset or speakerphone is handy, and at night there is no need to keep the phone under your pillow: you can simply leave it next to you.
This is ordinary caution, not protection against a proven harm.
Through the body
The human body is mostly water, and water absorbs radio waves well, more so at higher frequencies. At 2.4 GHz the wave penetrates a few centimetres into tissue and dies out there; lower frequencies go deeper.
In practice:
- a person standing between router and phone noticeably weakens WiFi; a room full of people has worse signal than an empty one;
- a phone in a back pocket or gripped tightly in the hand gets worse reception;
- Bluetooth earbuds sometimes stutter when the phone is in a pocket on the other side of your body: the signal has to go through you.
Decibels without fear
A decibel (dB) is not a unit of power but a way of writing a ratio between two powers. It is logarithmic: multiplication turns into addition, which makes the arithmetic easier for radio engineers.
| Change | What it means for power |
|---|---|
| +3 dB | twice as much |
| −3 dB | half as much |
| +10 dB | ten times as much |
| −10 dB | a tenth |
| +20 dB | a hundred times as much |
| −30 dB | a thousandth |
dBm and dBi
dBm is decibels relative to one milliwatt. That makes it an actual power:
| dBm | Power | Example |
|---|---|---|
| 33 dBm | 2 W | maximum phone power on a GSM 900 network |
| 20 dBm | 100 mW | the maximum allowed 2.4 GHz WiFi power in Europe (antenna included) |
| 0 dBm | 1 mW | a low-power Bluetooth device |
| −50 dBm | 10 nW | very strong WiFi signal next to the router |
| −70 dBm | 0.1 nW | a typical working WiFi signal |
| −90…−100 dBm | 1–0.1 pW | the edge where the connection still holds |
Only a tiny fraction of the router's power reaches the phone, and that is normal for radio: receivers are sensitive to incredibly weak signals.
dBi is antenna gain compared with an imaginary antenna that radiates equally in all directions. An antenna does not create energy out of nothing: "gain" means it concentrates power in a particular direction, taking it away from others. A 9 dBi antenna shines a narrow beam further in one direction but does worse in the others than an ordinary whip antenna. So a directional antenna only helps when it is pointed at the right spot.
Link budget
Whether there is enough signal is worked out like a household budget: what the transmitter puts in, what the antennas add, what distance and walls take away.
Distance in free space takes this much (at 2.4 GHz, calculated):
| Distance | Loss |
|---|---|
| 1 m | 40 dB |
| 10 m | 60 dB |
| 100 m | 80 dB |
| 1 km | 100 dB |
The frequency dependence here is the same antenna-size effect described above. Each doubling of distance adds 6 dB of loss. Hence the rule: every 6 dB of margin roughly doubles the range in free space. Indoors, where walls get in the way, range grows more slowly.
Example: a router in the hallway, a phone in a room behind two brick walls, 10 m away.
| Item | dB |
|---|---|
| router power | +18 dBm |
| router antenna | +2 dBi |
| phone antenna | 0 dBi |
| 10 m of air | −60 dB |
| two brick walls (roughly) | −15 dB |
| at the phone's input | ≈ −55 dBm |
That is a good signal. Now swap the brick for two concrete walls at 15–20 dB each: you get about −70…−80 dBm, the edge of comfortable use. That is why one access point for a whole flat in a concrete panel block often is not enough.
Will a booster help
WiFi. What works best is a second access point connected by cable, or a mesh system: several access points working as one network. A simple repeater (often sold as a "WiFi booster") receives the signal and retransmits it on the same radio, so it spends half its airtime relaying, and where it sits the signal from the router is already weak. If you can run a cable, that is the most reliable option; if not, go for mesh, ideally with a separate band for the link between the units.
A directional antenna for a modem. For a 4G router or modem in a house, an external directional antenna on the roof, pointed at the mast, is a very effective option: the modem hears the mast better and the mast hears the modem better, so the network itself lowers the modem's power and there is less interference around. Whether it needs a permit depends on the country: ask your operator. ⚠ A directional antenna on a WiFi router used to link two buildings adds its gain to the allowed power: turn the transmitter down so that, together with the antenna, it stays within the limit, or use a ready-made point-to-point kit that takes this into account.
Mobile signal boosters (repeaters). These devices pick up the mast's signal, amplify it and retransmit it indoors, and send the phone's signal back to the mast. In Ukraine they may only be installed if they are certified and approved by the operator. Cheap unapproved repeaters from online shops often start oscillating and spewing noise, and that jams the mast for every customer nearby, not just the owner. Such devices are tracked down and switched off.
Legal options if mobile signal at home is poor:
- talk to your operator: they may offer an approved solution or tell you which equipment is permitted;
- WiFi calling (VoWiFi) if you have internet at home;
- a 4G router with an external antenna for internet, plus WiFi calling.
Booster stickers and "signal-boosting" cases. A sticker on the back of the phone or an "antenna" case cannot improve reception: they have no power, no connection to the phone's antenna, and their size and shape are not tuned to mobile frequencies. Metal parts in such a case can even make the signal worse.
⚠ Signal jammers and home-made increases in transmitter power are illegal and interfere with other people, including those who need to call for help. We do not cover them here.
What to do when the signal is poor
| Problem | What to try |
|---|---|
| weak WiFi in the far room | put the router in the middle of the flat, up high, not in a cupboard; add a cabled access point or mesh |
| strong WiFi signal but low speed | switch to 5 GHz; on 2.4 GHz use channel 1, 6 or 11 and 20 MHz width |
| WiFi drops when the microwave is on | switch to 5 GHz; on 2.4 GHz use channel 1 |
| mouse or headset lags next to the laptop | move the receiver away from the USB 3.0 ports with an extension cable |
| poor mobile signal indoors | get to a window facing the mast, go higher up; use WiFi calling |
| calls drop, phone flips between 4G and 3G | lock the network mode in the settings |
| there is signal but data barely works | check RSRP and SINR: weak signal, look for a better spot; poor SINR, try another band |
| a house far from the mast | a 4G router with a directional antenna on the roof; WiFi calling |
| signal is worse in a new building than in the old one | energy-saving glass: open a window, use the balcony, use WiFi calling |
| no network at all out in the country | get to open ground or a hill; if your operator supports satellite service, text via satellite |
| tempted to install a booster | only one approved by your operator; stickers and cases do not work |
Sources
- VEON: Kyivstar launches Starlink Direct to Cell in Ukraine
- Kyivstar: 3 million customers registered for Starlink Direct to Cell
- Kyivstar: light data via Starlink (Nasdaq)
- Interfax-Ukraine: Kyivstar and Starlink Direct to Cell
- BGR: Starlink Direct to Cell explained
- The Grid: Starlink Direct to Cell explained
- Starlink: Direct to Cell
- T-Mobile: T-Satellite
- ICNIRP: guidelines on radiofrequency fields (2020)
- IARC: radiofrequency fields classified as Group 2B (press release, 2011)
- Karipidis et al., 2024: systematic review, Environment International
- WHO: questions and answers on electromagnetic fields
- FDA: microwave oven radiation
- Intel: USB 3.0 interference with 2.4 GHz wireless devices
- ITU-R P.2040: effects of building materials on radio wave propagation